|
|
GROUP OF COMPANIES
IZOMETÒ SLS
HB0101 IZOMETÒ Self Leveling Screed DATA SHEET
3 mm EPOXY FLOOR
|
DESCRIPTION |
IZOMETÒ Self Leveling Screed has 3
mm thickness at all and provides anti-bacterial (seamless), hard wearing,
attractive floor and also has
resistance to most dilute chemicals, impervious and easy to clean.
IZOMETÒ Self Leveling Screed is a
blend of epoxy resins and well granulated special silica aggregates. Has three
components.
Each pack contains three components which
is factory weighed an packaged so ready
for site usage.
Also a pre-packaged primer (IZOMET® Primer SF) is
supplied.
|
APPLICATION AREAS |
IZOMETÒ Self Leveling Screed is
ideal to use in offices, showrooms,
shopping centers, hospitals, clean room facilities, laboratories, pharmacies,
switch gear plant rooms etc. and any application needs hygienic,
attractive and ease to clean surfaces.
|
SPECIAL
FEATURES |
·
Solvent-free, low odor
·
Anti-bacterial, seamless
·
Hard wearing
·
Good chemical resistant
·
Easy to clean
·
Attractive
·
Available in all RAL colors
|
PHYSICAL PROPERTIES |
|
Property |
10°C |
20°C |
30°C |
|
Primer pot
life |
40 min |
35 min |
12 min |
|
Screed pot
life |
80 min |
45 min |
25 min |
|
Primer curing
time |
90 min |
50 min |
25 min |
|
Screed curing
time |
30 hr |
15 hr |
8 hr |
|
Full cure |
7 days at room |
temperature |
|
|
MECHANICAL PROPERTIES |
|
Property |
Typical
Result |
|
Compressive
strength |
65 N/mm² |
|
Flexural
strength in tension |
25 N/mm² |
|
Adhesion to
concrete |
4-5 N/mm² |
|
Modulus of
elasticity |
5500 N/mm² |
|
Density |
1,7 g/cm³ |
All tests made after full cure
|
CHEMICAL PROPERTIES |
|
Water,
de-ionized |
|
+ |
|
Javelle Water |
14% |
+ |
|
Sulfuric acid |
10% |
+ |
|
|
30% |
+ |
|
Nitric acid |
30% |
+ |
|
Acetic acid |
10% |
° |
|
Caustic soda |
20% |
+ |
|
Gasoline,
leaded (petrol) |
|
+ |
|
Toluene |
|
+ |
|
Xylene |
|
+ |
|
Styrene |
|
+ |
|
111-trichloroethane |
|
+ |
|
Skydrol 500 A
(hydraulic fluid) |
|
+ |
|
Octanol |
|
+ |
|
Fruit juices |
|
+ |
|
Sugar
solution |
|
+ |
|
Key : + unaffected |
|
|
|
° yellowing |
|
|
Samples were submerged in test reagents for 12 months at 20°C.
|
INSTRUCTIONS
FOR USE |
·
SURFACE PREPARATION
Concrete or cement substrates
should be 28 days old and moisture content of substrate should be less than 5%
at least. All latience and loose materials must be removed from the concrete
surface.
Cracked or damaged substrate
should be repaired with Izomet®
Repair Mortar before application. Then all dust and debris should be
removed. Oil or grease contaminated surfaces should be cleaned by a suitable
detergent.
·
MIXING COMPONENTS
If possible mix all the components with a
mixer running at less than 400 rpm to avoid trapping air in material.
·
PRIMING
Only IZOMET®
Primer SF used for priming. Mix resin and hardener until a uniform
consistency is achieved. Apply with stiff brushes or rollers and layer must be
like thin continuous film. Highly porous substrates may require two coats of
priming.
·
LAYING THE SCREED
IZOMETÒ Self Leveling Screed is
supplied in pre-weighed packs in exact proportions.
Mix resin and hardener until a uniform
consistency is achieved. Then add aggregate slowly and continue to mix at least
5 seconds with mechanical mixer.
After mixing pour the screed to floor and
spread with a toothed trowel to get 3 mm thickness. Use spiked nylon roller to
release trapped air and level any slight trowel marks. Rolling must be continue
until all air has been released.
·
ANTI-SKID FINISH
If required use IZOMET® Anti-Skid Granules to get non-slip surface. Apply material to wet surface by spraying and
use approximately 0,1 kg/m².
|
CURING |
After application foot traffic must be
prohibited until reaching initial hardness. Heavy traffic and chemicals should
not be allowed before full cure (7 days).
|
CLEANING |
After the application, all hand tools and
other surfaces effected from uncured epoxy resin should be cleaned with Izomet®
Cleaning fluid.
|
COVERAGE |
IZOMET® Primer SF (5 kg pack) :
Covers 15-20 m².
IZOMET® SLS (30 kg pack) :
Covers 6 m² approximately.
IZOMET® Anti-skid granules (30 kg pack) : Covers 300 m² approximately.
|
STORAGE |
All materials should be kept in their tightly closed own packs. Under
these conditions shelf life is minimum 12 months at normal temperatures.
|
CAUTION |
Uncured epoxy resin kept away
from mouth, eyes, food or drink.
Empty tins must not be used
even cleaned by suitable methods.
During application or handling
uncured epoxy resins, wear gloves or barrier creams.
In case of contact with skin
immediately clean with warm water and soap.
Avoid inhaling vapor.
Do not use below 5°C.
No other materials should be
added.
|
SUPPLY |
IZOMAS GROUP OF COMPANIES
Headquarters
Cumhuriyet mah. Fatih cad. No:4
Kartal - Istanbul - TURKEY
Tel: +90 216 451 48 48 (PBX)
Fax: +90 216 309 74 57
http:\\www.izomas.com.tr
e-mail: izomas@izomas.com.tr
Izomet is a IZOMAS trade mark. This
material is manufactured in Turkey using raw material from and under the
supervision of Shell Chemicals. The information that given in this leaflet is, prepared best of our
current knowledge and given in good faith, but our recommendations are made
without guarantee because of the
conditions of uses are beyond our control. Buyers and applicators should
prepare their own instructions for their own conditions and requirements.