GROUP OF COMPANIES

IZOMET^Ò Multilayer Screed

HB0102

3 mm Non-Slip Epoxy Floor

DATA SHEET

DESCRIPTION

IZOMET^Ò Multilayer Screed has 3 mm thickness at all and provides non-slip, anti-bacterial (seamless), hard wearing, attractive floor and also has good comprehensive strength, resistance to most dilute chemicals, impervious and easy to clean.

IZOMET^Ò Multilayer Screed is a blend of epoxy resins and well granulated special silica aggregates. Has two materials and applied in three layers. Two layers of IZOMET^Ò Multilayer Primer and IZOMET^Ò Multilayer Screed Topping.

IZOMET^Ò Multilayer Primer is a three component system which is factory weighed and packaged so ready for site usage. It’s applied with toothed trowel and sprinkled with well granulated special quartz sand. IZOMET^Ò Multilayer Primer applied in two layer and get approximately 2,5-3 mm thickness.

IZOMET^Ò Multilayer Screed Topping is a two component system which is factory weighed an packaged so ready for site usage. It’s colored epoxy system applied for finishing to get attractive and easy cleaning surface.

APPLICATION AREAS

IZOMET^Ò Multilayer Screed is ideal for use in abattoirs and meat processing plants, dairies and bakeries, hospital, restaurant, canteen and other bulk, catering kitchens, factories and assembly plants, offshore platforms, printing shops, cold storage facilities etc. and any application needs non-slip, strong, hard wearing, hygienic, attractive and ease to clean surfaces.

SPECIAL FEATURES

· Tough non-slip surface

· Anti-bacterial, seamless

· Hard wearing

· Good chemical resistant

· Easy to clean

· Attractive

· Available in all RAL colors

PHYSICAL PROPERTIES

Property	10°C	20°C	30°C
1^st and 2^nd layer pot life	80 min	55 min	20 min
Finishing Later pot life	70 min	55 min	15 min
1^st and 2^nd layer curing time	40 min	20 min	10 min
Finishing Later curing time	40 min	15 min	10 min
Full cure	7 days at room	temperature

MECHANICAL PROPERTIES

Property	Typical Result
Compressive strength	70 N/mm²
Flexural strength in tension	25 N/mm²
Adhesion to concrete	4-5 N/mm²
Modulus of elasticity	10000 N/mm²
Density	2,0 g/cm³

All tests made after full cure

CHEMICAL PROPERTIES

Water, de-ionized		+
Javelle Water	14%	+
Sulfuric acid	10%	+
	30%	+
Nitric acid	30%	+
Acetic acid	10%	°
Caustic soda	20%	+
Gasoline, leaded (petrol)		+
Toluene		+
Xylene		+
Styrene		+
111-trichloroethane		+
Skydrol 500 A (hydraulic fluid)		+
Octanol		+
Fruit juices		+
Sugar solution		+
Key : + unaffected
° yellowing

Samples were submerged in test reagents for 12 months at 20°C.

INSTRUCTIONS FOR USE

· SURFACE PREPARATION

Concrete or cement substrates should be 28 days old and moisture content of substrate should be less than 5% at least. All latience and loose materials must be removed from the concrete surface.

Cracked or damaged substrate should be repaired with Izomet^® Repair Mortar before application. Then all dust and debris should be removed. Oil or grease contaminated surfaces should be cleaned by a suitable detergent.

· MIXING COMPONENTS

If possible mix all the components with a mixer running at less than 400 rpm to avoid trapping air in material.

· PRIMING (first two layers)

Only IZOMET^® Multilayer Primer used for priming. Mix resin and hardener until a uniform consistency is achieved. Apply with toothed trowel to get 0,7-0,9 mm thick layer by using approximately 1,0-1,2 kg per square meter. Then sprinkle 0,4-0,8 mm size range of quartz sand, to the surface.

After reaching the initial hardness brush all loose materials from surface. Then apply second layer with normal steel trowel and spend 1,7-1,9 kg/m² mix to get 1 mm thickness and to all surface with quartz sand. After reaching initial hardness brush all loose material again.

· TOPPING LAYER

IZOMET^Ò Multilayer Screed Topping is also supplied in pre-weighed packs in exact proportions.

Mix colored resin and hardener until a uniform consistency is achieved. After mixing pour the screed to floor and spread with steel trowel. Scrape the mix firmly up to the priming layer in all directions and be sure that material penetrates fully to the previous layer and expels all air. Unless air bubbles may exist during curing. Finally scrape away all excess resin by a steel trowel.

CURING

After application foot traffic must be prohibited until reaching initial hardness. Heavy traffic and chemicals should not be allowed before full cure (7 days).

CLEANING

After the application, all hand tools and other surfaces effected from uncured epoxy resin should be cleaned with Izomet^® Cleaning fluid.

COVERAGE

IZOMET^® Multilayer Primer (10 kg pack) : Covers 3,3-3,7 m².

IZOMET^® Multilayer Screed Topping (2,5 kg pack) : Covers 4-5 m²

STORAGE

All materials should be kept in their tightly closed own packs. Under these conditions shelf life is minimum 12 months at normal temperatures.

CAUTION

Uncured epoxy resin kept away from mouth, eyes, food or drink.

Empty tins must not be used even cleaned by suitable methods.

During application or handling uncured epoxy resins, wear gloves or barrier creams.

In case of contact with skin immediately clean with warm water and soap.

Avoid inhaling vapor.

Do not use below 5°C.

No other materials should be added.

SUPPLY

IZOMAS GROUP OF COMPANIES

Headquarters

Cumhuriyet mah. Fatih cad. No:4

Kartal - Istanbul - TURKEY

Tel: +90 216 451 48 48 (PBX)

Fax: +90 216 309 74 57

http:\\www.izomas.com.tr

e-mail: izomas@izomas.com.tr

Izomet is a IZOMAS trade mark.

This material is manufactured in Turkey using raw material from and under the supervision of Shell Chemicals.

The information that given in this leaflet is, prepared best of our current knowledge and given in good faith, but our recommendations are made without guarantee because of the conditions of uses are beyond our control. Buyers and applicators should prepare their own instructions for their own conditions and requirements.