GROUP OF COMPANIES

IZOMET^Ò MARINE

HB0116

Epoxy Based Repair Mortar For Underwater Works

DATA SHEET

DESCRIPTION

IZOMET^Ò Marine is a three component, epoxy resin + special hardener + well granulated quartz aggregates (if needed) system that has excellent facilities. It’s specially developed for underwater works and it can be used as a non shrink repair mortar or filling mortar that has excellent adhesion ability to metal, concrete etc. surfaces.

The special formulation of IZOMET^Ò Marine is suitable for underwater repairing works such as marine structure’s piles and/or surfaces and also has resistant to aggressive effects of sea water and splash zone.

IZOMET^Ò Marine can be applied, because of low modulus of elasticity, onto the steel pipes that crosses concrete, as a non shrink grout and water insulation material.

IZOMET^Ò Marine is a two component coating system which is factory weighed an packaged so ready for site usage and is a blend of special epoxy resins.

SPECIAL FEATURES

· Suitable for all kind of underwater works

· Protects structure from corrosion

· Resistant to most chemicals

· High load carrying capacity

· Non shrink

· Low creep

· Well adhesion to concrete and/or steel

PHYSICAL PROPERTIES

Property	20°C
Pot life (for 100 g mix)	60 min
Initial hardness	24 hr
Full cure	7 Days

MECHANICAL PROPERTIES

Property
Adhesion to blasted steel	4 N/mm²
Comprehensive strength	35 N/mm²
E-modulus	15000 N/mm²
Temperature strength	< 80°C

All tests made after full cure

INSTRUCTIONS FOR USE

· PREPARATION

For best adhesion, all dust and debris should be removed from surface. Oil or grease contaminated surfaces should be cleaned by a suitable detergent.

· MIXING COMPONENTS

IZOMET^Ò Marine is a three component material and supplied in pre-weighed packs in exact proportions. If possible mix all the components with a mixer running at less than 400 rpm to avoid trapping air in material.

· APPLICATION

If IZOMET^Ò Marine is used for fillings only pour the mixture to the formwork. For repair mortar applications it applied by hand. Press hand full of mixture to application area. Fill the gap by this way.

CURING

Application can be made between 5°C to 30°C. If application in over temperature places call our technical service for help.

Full cure takes 7 days.

CLEANING DOWN

After application all hand tools and other surfaces effected from uncured epoxy resin should clean with Izomet^® Cleaning fluid.

CONSUMPTION

IZOMET^® Marine is supplied in 5 kg pre-weighed packages. Density is between 1,50-2,20 kg /dm³ (related to the amount of third component)

STORAGE

All materials should be kept in their tightly closed own packs. Under these conditions shelf life is minimum 12 months at normal temperatures.

CAUTION

Uncured epoxy resin kept away from mouth, eyes, food or drink.

Empty tins must not be used even cleaned by suitable methods.

During application or handling uncured epoxy resins, wear gloves or barrier creams.

In case of contact with skin immediately clean with warm water and soap.

Avoid inhaling vapor.

Do not use below 5°C.

No other materials should be added.

SUPPLY

IZOMAS GROUP OF COMPANIES

Headquarters

Cumhuriyet mah. Fatih cad. No:4

Kartal - Istanbul - TURKEY

Tel: +90 216 451 48 48 (PBX)

Fax: +90 216 309 74 57

http:\\www.izomas.com.tr

e-mail: izomas@izomas.com.tr

Izomet is a IZOMAS trade mark.

This material is manufactured in Turkey using raw material from and under the supervision of Shell Chemicals.

The information that given in this leaflet is, prepared best of our current knowledge and given in good faith, but our recommendations are made without guarantee because of the conditions of uses are beyond our control. Buyers and applicators should prepare their own instructions for their own conditions and requirements.