|
|
GROUP OF COMPANIES
IZOMETÒ Laminating System
HB0118 Laminating
Coatings For Chemical Resistant DATA SHEET
|
DESCRIPTION |
IZOMETÒ Laminating System can be
applied to tanks, storage plants etc. under effect of aggressive chemicals. It also
protects the structure (concrete or steel) against corrosive chemicals or
something else.
IZOMETÒ Laminating System is a two
component special solvent free epoxy + hardener system that applied with glass
mat.
Each pack is factory weighed an
packaged so ready for site usage.
|
APPLICATION AREAS |
IZOMETÒ Laminating System is ideal
for use places under chemical materials such as storage areas of chemicals,
dilute acid tanks, ballast tanks, production plants under effect of chemicals, chemical
processing plants, etc. and any application needs highest chemical performance.
|
SPECIAL
FEATURES |
·
Highest chemical performance
·
Hard wearing
·
Solvent free
·
Prevents further corrosion
·
Easy to clean
·
Non-slip
·
Available in all RAL colors
|
PHYSICAL PROPERTIES |
|
Property |
20°C |
30°C |
|
Pot life (for
100 g mix) |
30 min |
15 min |
|
Re-coating
time |
12 hr |
6 hr |
|
Initial cure |
36 hr |
24 hr |
|
Full cure |
7 days at room |
temperature |
|
CHEMICAL PROPERTIES |
|
Sea water |
|
+ |
|
Sulfuric acid |
10% |
+ |
|
|
30% |
+ |
|
Hydrochloric
acid |
10% |
+ |
|
|
20% |
° |
|
Caustic soda |
10% |
+ |
|
|
30% |
° |
|
Ammonia |
10% |
+ |
|
|
25% |
° |
|
Acetic acid |
10% |
+ |
|
|
50% |
° |
|
Lactic acid |
10% |
+ |
|
Linseed oil
fatty acid |
|
+ |
|
Tall oil
fatty acid |
|
+ |
|
Xylene |
|
+ |
|
Gasoline |
|
+ |
|
Crude oil |
|
+ |
|
Key : + unaffected |
|
|
|
° yellowing |
|
|
Samples were submerged in test reagents for 12 months
at 20°C.
|
INSTRUCTIONS
FOR USE |
·
SURFACE PREPARATION
Steel structures should be free from rust,
oil or any foreign materials. If rust isn’t so much, manual cleaning could be made
but for the best result sand or grit blast the steel surface according to the
Swedish Standard SA 2½.
Concrete or cement substrates
should be 28 days old and moisture content of substrate should be less than 5%
at least. All latience and loose materials must be removed from the concrete
surface.
Cracked or damaged substrate
should be repaired with Izomet®
Repair Mortar before application. Then all dust and debris should be
removed. Oil or grease contaminated surfaces should be cleaned by a suitable
detergent.
·
MIXING COMPONENTS
If possible, mix all the components with a
mixer running at less than 400 rpm to avoid trapping air in the material. For
mixing mortar use forced action mixer. Do not use fall mixers.
·
PRIMING
Only IZOMET®
Laminating System Primer used for priming. Mix resin and hardener until a
uniform consistency is achieved. Apply with stiff brushes or rollers and layer
must be like thin (not more than 30 microns) continuous film. Highly porous
substrates may require two coats of priming.
·
LAMINATING
IZOMETÒ Laminating System is
supplied in pre-weighed packs in exact proportions. Mix resin and hardener
until a uniform consistency is achieved.
Apply the mixture to the primed surface by
rollers. Then begin to lay glass mate as quick as possible. System must be made
as wet-on-wet. Then again apply the
mixture of IZOMET® Laminating
System over glass mat. Be sure that glass mat is fully absorbed resin + hardener.
Apply steel rollers to avoid trapping air after each layer carefully.
|
CURING |
After application foot traffic must be
prohibited until reaching initial hardness. Heavy traffic and chemicals should
not be allowed before full cure (7 days).
|
CLEANING |
After application all hand tools and other
surfaces effected from uncured epoxy resin should be cleaned with Izomet®
Cleaning fluid.
|
COVERAGE |
IZOMET® Laminating System (10 kg pack) : Covers 3-5 m²
|
STORAGE |
All materials should be kept in their tightly closed own packs. Under
these conditions shelf life is minimum 12 months at normal temperatures.
|
CAUTION |
Uncured epoxy resin kept away
from mouth, eyes, food or drink.
Empty tins must not be used
even cleaned by suitable methods.
During application or handling
uncured epoxy resins, wear gloves or barrier creams.
In case of contact with skin
immediately clean with warm water and soap.
Avoid inhaling vapor.
Do not use below 5°C.
No other materials should be
added.
|
SUPPLY |
IZOMAS GROUP OF COMPANIES
Headquarters
Cumhuriyet mah. Fatih cad. No:4
Kartal - Istanbul - TURKEY
Tel: +90 216 451 48 48 (PBX)
Fax: +90 216 309 74 57
http:\\www.izomas.com.tr
e-mail: izomas@izomas.com.tr
Izomet is a IZOMAS trade mark. This
material is manufactured in Turkey using raw material from and under the
supervision of Shell Chemicals. The information that given in this leaflet is, prepared best of our
current knowledge and given in good faith, but our recommendations are made
without guarantee because of the
conditions of uses are beyond our control. Buyers and applicators should
prepare their own instructions for their own conditions and requirements.