GROUP OF COMPANIES

IZOMET^Ò Epoxy Steel Primer/SF

HB0111

Anti-Corrosion Primer For Steel (Solvent Free)

DATA SHEET

DESCRIPTION

IZOMET^Ò Epoxy Steel Primer S/F has excellent mechanical facilities so it can afford perfect out standing protection against corrosion and any other atmospheric or environmental conditions. And also IZOMET^Ò Epoxy Steel Primer S/F can be used for repairing works that made with Izo-BTS^Ò Process System as a protection for reinforcing bars.

IZOMET^Ò Epoxy Steel Primer S/F is ideal to protect steel structures such as marine structuress, petrochemical plants, bridges any structure under affect of corrosive attacks. And also it’s suitable for repairing of pre-coated steel elements.

IZOMET^Ò Epoxy Steel Primer S/F is a two component coating system which is factory weighed an packaged so ready for site usage and is a blend of special epoxy resins.

SPECIAL FEATURES

· Solvent free

· Positive bond to steel

· Well adhesion

· Rust inhibiting

· Hard flexible surface coating

· If needed diluted with solvents

· Excellent resistance to humidity, water and dilute chemicals

PHYSICAL PROPERTIES

Property	10°C	20°C	30°C
Pot life	60 min	40 min	30 min
Initial hardness	10 hr	6 hr	3 hr
Re-coating time	8-20 hr	4-12 hr	2-8 hr
Full cure	7 Days	at room	temperature

MECHANICAL PROPERTIES

Property	20°C	40°C	60°C
Hardness (Perzos)	36 sec	115 sec	-
Initial hardness	7 hr	-	5 hr
Impact Strength (1 kg/point f20 mm)	80 cm.kg	-	60 cm.kg
Bend Test (15 mm Mandrel)	180°	-	135°

All tests made after full cure

INSTRUCTIONS FOR USE

· PREPARATION

Steel structures should be free from rust, oil or any foreign materials. If rust isn’t so much manual cleaning could be made but for the best result sand or grit blast the steel surface to the Swedish Standard SA 2½.

· MIXING COMPONENTS

IZOMET^Ò Epoxy Steel Primer S/F is a three component material and supplied in pre-weighed packs in exact proportions. If possible mix all the components with a mixer running at less than 400 rpm to avoid trapping air in mixture.

· APPLICATION

IZOMET^Ò Epoxy Steel Primer S/F can be applied by airless spray, roller or brush. During application be careful not to leave pinholes or breaks in the coating.

For the best adhesion between layers also be careful about application times (re-coating time) between the two layer. System must be made as wet-on-wet. Unless blast or emery existing layer.

CURING

Application can be made between 5°C to 30°C. If application in over temperature places call our technical service for help.

Full cure takes 7 days.

CLEANING DOWN

After the application, all hand tools and other surfaces effected from uncured epoxy resin should be cleaned with Izomet^® Cleaning fluid.

COVERAGE

IZOMET^® Epoxy Steel Primer S/F is supplied in 5,7 kg pre-weighed packages. Usage is about 200 g/m² and covers approximately 28 m² area.

STORAGE

All materials should be kept in their tightly closed own packs. Under these conditions shelf life is minimum 12 months at normal temperatures.

CAUTION

Uncured epoxy resin kept away from mouth, eyes, food or drink.

Empty tins must not be used even cleaned by suitable methods.

During application or handling uncured epoxy resins, wear gloves or barrier creams.

In case of contact with skin immediately clean with warm water and soap.

Avoid inhaling vapor.

Do not use below 5°C.

No other materials should be added.

SUPPLY

IZOMAS GROUP OF COMPANIES

Headquarters

Cumhuriyet mah. Fatih cad. No:4

Kartal - Istanbul - TURKEY

Tel: +90 216 451 48 48 (PBX)

Fax: +90 216 309 74 57

http:\\www.izomas.com.tr

e-mail: izomas@izomas.com.tr

Izomet is a IZOMAS trade mark.

This material is manufactured in Turkey using raw material from and under the supervision of Shell Chemicals.

The information that given in this leaflet is, prepared best of our current knowledge and given in good faith, but our recommendations are made without guarantee because of the conditions of uses are beyond our control. Buyers and applicators should prepare their own instructions for their own conditions and requirements.