GROUP OF COMPANIES
 
 

 


IZOMETÒ BRM

 

 

 

HB0113

 

IZOMETÒ Repair Mortar

 

 

DATA SHEET

 
 
 

 

 


Polymer Modified Cement Based Repair Mortar

 

    DESCRIPTION

     IZOMETÒ BRM is a polymer modified cement based repair mortar with high elasticity and adhesion quantities, containing specially treated quartz sand, high quality Portland cement, polypropylene and steel fiber reinforcements and special Polymer Dispersions. Can be applied centimeter (from 1 cm to 10 cm) thickness.

     IZOMETÒ BRM is used as a part of Izo-BTSÒ (see the data sheets for more detail) concrete repairing system. It can be applied both vertically and horizontally to concrete structures under effect of corrosion. IZOMETÒ BRM can be used for improvement and/or repair works of concrete properties such as corroded, defective, dusty, highly porous concrete surfaces etc.. IZOMETÒ BRM may also improve the corrosion resistance of structural reinforcement.

     IZOMETÒ BRM is a two component system which is factory weighed an packaged  so ready for site usage.

SPECIAL FEATURES

 

·       Ease of application

·       High adhesion to substrate

·       Low E-Modules

·       Higher compression strength at new mortar

·       Very low risk of cracks

·       High abrasion resistance

·       Higher resistance to freeze and thaw circle

·       Increases the resistance of substrate to aggressive environmental effects

 

 

    PHYSICAL PROPERTIES

 

Property

 

Pot life

Approximately 30 min @ 20°C

Setting Period

Approximately 12 hr

Min. coat thickness

1 mm/coat

Range of coating thickness

min. 10 mm - max. 100 mm

Elasticity Modulus

32000 N/mm²

Granule size

Approximately 0,400 mm

Compressive Strength

Approximately 60 N/mm² @ 28 day

Flexural Strength

Approximately 12 N/mm² @ 28 day

Adhesion to Concrete

Excellent

Min. application temperature

5°C

Density

2.0 kg/dm³

All tests made after full cure

 

 

INSTRUCTIONS FOR USE

·       MIXING COMPONENTS

     IZOMETÒ BRM is a two component material and supplied in pre-weighed packs in exact proportions. Slowly add Part A to Part B while stirring. If possible mix all the components with a mechanical mixer until a uniform consistency is achieved.

·       APPLICATION

     If IZOMETÒ BRM is used for corrosion repairing works, use Izo-BTSÒ (see the data sheets for more detail) concrete repairing system, firstly remove the corroded concrete. The substrate should be structurally firm and free from oils and chemicals. if not apply proper surface cleaning methods such as sand blasting, wire brushing, chiseling out of unsound parts etc.. Then apply IZOMETÒ HOLD polymer primer to all surface. The mixture of IZOMETÒ BRM can be applied with trowel or plasterer’s float. It applied in layers of min 10 mm thickness. No other additives, under no circumstances, may be added to the mortar.

 

    CONSUMPTION

     IZOMET® ARM is supplied  in 58 kg pre-weighed packages (50 kg Part B + 8 kg Part A). Usage is about 20 kg/m² and gives approximately 10 mm thickness.

 

    STORAGE

     All materials should be kept  in their tightly closed own packs. Under these conditions shelf life is minimum 12 months at normal temperatures and humidity conditions.

    CAUTION

     Concrete surfaces must be at least 28 days old.

     Substrate temperature must be between +5 - 30°C

     All two components should kept away from mouth, eyes, food or drink.

     Empty tins must not be used even cleaned by suitable methods.

     Because of materials high pH (pH 11-12) value, during application or handling wear gloves or barrier creams. Avoid direct contact with skin and eyes.

     In case of contact with skin immediately clean with warm water and soap.

     Do not use below 5°C and/or above 90% humidity.

     No other materials should be added.

 

    SUPPLY

 

IZOMAS GROUP OF COMPANIES

Headquarters

Cumhuriyet mah. Fatih cad. No:4

Kartal - Istanbul - TURKEY

Tel: +90 216 451 48 48 (PBX)

Fax: +90 216 309 74 57

http:\\www.izomas.com.tr

e-mail: izomas@izomas.com.tr

Izomet is a IZOMAS trade mark.

This material is manufactured in Turkey using raw material from and under the supervision of Synthomer GmbH.

 

The information that given in this leaflet is, prepared best of our current knowledge and given in good faith, but our recommendations are made without guarantee because of   the conditions of uses are beyond our control. Buyers and applicators should prepare their own instructions for their own conditions and requirements.